Flanger This effect layers four chorus sounds to produce even more Add Metallic Resonance to the Sound depth and spaciousness than a conventional chorus. Page 58 Chapter 4 Setting Effects This is a flanger that changes the pitch of the sound in steps. HPF: The frequency range below the cutoff frequency The frequency of pitch change can also be synchronized to will be cut. Page 59 Chapter 4 Setting Effects Short Delay Auto PAN Automatically Move the Add Echoes to the Sound Stereo Location This is a short delay which allows you to set the left and right This effect automatically moves the stereo location of the delay times independently.
Feedback Pitch Shifter effect. Skew the Pitch Range: 0— This effect shifts the pitch of the original sound and layers it Reverb Add Reverberation with the original sound. It can be used to play unison lines at an interval of an octave or fifth, or to layer a slightly pitch- This effect adds reverberation and ambiance to the sound, shifted with the original sound to create a chorus effect. Gated Reverb Isolator Cuts Off a Specific Range Sharply Cut the Reverberation An equalizer which cuts the volume greatly, allowing you to This is a type of reverb, in which the reverberation is cut off add a special effect to the sound by cutting the volume in varying ranges.
Professional DJ Mixer. To disable it, set greater number of onboard effects, you can now create it to OFF. Page 65 refer to Playing Back in Arpeggio Arpeggiator p. During recording, press [REC] button. Press the [HOLD] button. Turning these 3. Set the MC to the Recording mode. Press the [F4 PRM4 ] button. You can play back the Rhythm Set. Make the preparations for recording Page Recording Mode Mute button, refer to P. Procedure Press the [PACH] button. Recording mode. Now, the keyboard pads have been switched back to the mode in which you set the note input timing.
The note will be deleted. If you wish to keep the pattern that you created, you must use the Pattern Write - Note name: C-1—G9 operation. On the other hand, the MC may fail to receive the bulk dumps from the MC due to differences in the number of patches.
Values Changes existing data settings. With this function, you can view specific data to facilitate searching for the desired performance data. Procedure Procedure 1. Copying is executed and, upon completion, the normal Erases part or all of a pattern. Procedure Select a pattern for which Erase is to be executed. Available Settings: 1. If you wish to add more Transposes the note number pitch for each part in a pattern.
Press the [F4 OK ] button. A screen asking you whether or not you want to execute A screen asking you whether or not you want to execute Change Gate Time appears. The Edit Quantize operation will be carried out, and the normal display will reappear.
Also, you can press [ ] button while the song is Songs stopped to return to the beginning. This will not affect the original pattern in any way, since the setup parameters for each pattern are Enter patterns one by one and specify the order in which stored as part of the song data.
This function is useful for playing two or more songs in sequence or for Clearing All Steps combining two or more songs. Page Saving The Song If you modified a song setting but do not want to save it, you can use it as it is the next time you power up the MC as long as you do not execute this function. This cursor below the tone number T-1 to T-4 for which you operation is referred to as patch editing or rhythm editing.
This boosts the waveform. Raising this setting 6 dB will double the gain. If you are using the booster to distort the sound, setting this to the maximum value will be effective. With negative - sound will appear more spacious the Detune effect. You can make settings for the four parameters TIME 1—4. Higher settings will result in a longer time until the next pitch level is reached. It will emphasize the mid- the frequency components of the waveform the Cutoff range, and is useful for creating a distinctive sound.
As this value is decreased, the cutoff frequency, adding character to the sound. This setting causes the stereo location to change randomly Bias Level Bias Level each time a note is played. All four indicators will be blinking, and the Random Pan Switch will be turned on. With negative - oscillations to sounds. Specifies whether or not the Velocity Range settings will be enabled. On the MC, the Turn this on when you wish to use portamento.
Page Chapter 6 Making Original Patches 7. All parameters explained in connection with patch editing can be saved. A rhythm set assigns a different tone to each keyboard pad.
To simulate this, you can and contents of the respective parameters. Raising this setting will also raise the cutoff frequency. The display shows the frequency of the A4 note. Select the destination part. Procedure 6. Press the keyboard pad associated with the key subject to The selection screen for system settings appears. Setting up the volume level of the 6. Page Chapter 7 Environment Configuration and 3. Press the [F3 SEQ ] button. Parameter Type: Backup parameters 4.
Press the [F2 PRM2 ] button. Transmitting synchronization 5. Page On the MC you can specify the playback timing of the phrase, so it will play back in precise synchronization with the pattern. Using this function enables different System Exclusive Procedure messages to be received by more than one MC unit at the 1. The selection screen for system settings appears. Page 2. Procedure The selection screen for system settings appears. On the other hand, the MC may fail to receive Caution: If any valuable data reside in the MC main This setting enables the part selected on the MC to be Page R of the MC to be played back.
Setting it to MIDI channels 1 to 7 enables patches selected with part 1 to 7. Press the [ ] button on the MC This setting enables the MC to output Returns to the beginning of pattern. Page Making playback on two units of the MC to be synchronized Two MC units can be connected to each other, and used to play different patterns in synchronization. Page Appendices Appendices The power of the MC or connected devices is not turned on. Notes Drop Out - Turn on the power. Check the tuning setting Refer to Tuning the entire - Set the contrast to an appropriate value.
If this does to process. Name No. The sound recordings contained in this product are the original works of Roland Corporation. Roland is not responsible for the use of the sound recordings contained in this product, and assumes no liability for any infringement of any copyright of any third party arising out of use of the sounds, phrases and patterns in this product.
S Dream Trance 4 B. S Dream Trance 5 B. Gabba Industry Fill 2 Name Meas. Piano Chord 1 E. Piano Chord 2 SFX 30 Beats Drums 1 Piano Chord 5 B. Beats Drums 2 Strings Latin 2 Crash Fill 12 Name Meas.
Keyboard Pad E. Fill 9 Synth Lead 11 Perc. Fill 10 SFX Data transmission Sequencer section 1 Recorded messages are transmitted during playback. Page Date : Oct. Page Index Saving Undo Techno, jungle, hip-hop, acid and other dance styles can now be approached easily and creatively by dance music producers and other groove enthusiasts with little or no musical training.
If you have questions about operating your Roland product, please check our Knowledge Base for answers to the most common questions. You can also contact our Product Support department by phone or email. Roland Users Group Read, watch, listen, and learn about Roland products and the people that use them. Email Support Get your questions answered by a Roland product specialist. Register Products Protect your investment. Stories Learn Discover Stories Spark creativity with in-depth writing on people, trends, tech, and history.
Learn Expand your knowledge with tutorials and guides from subject-matter experts.
0コメント